Beta Marine Engines

mikeB · mikeB

Here are pix of the heat exchanger-high rise exhaust elbow arrangement.MikeB

Williamdement · Williamdement

Williamdement wrote 2m, 22s ago:I did my seatrial w/my new bv1505 38 hp and cannot get up past 3000 rpms. I suspect that the prop is limiting. The prop is 18" with pitch of 12. The vessel is a Mariner 36 cutter. I get to hull speed at 2200 to 2500 rpms and after that notice a lot of extraneous water type...

Jenain · Jenain

I have just helped a friend save his Beta 50 that was flooded with salt water. The initial indication of trouble came, when his fully charged starter battery could not start the engine. On checking the oil, it was found to be a grey colour,(emulsified oil). The first, and most important job, was to fin...

Jefndeb · Jefndeb

I have a 2008 Beta 20 motor on my sailboat and I was think that I would like to display engine information on my chartplotter such as water temp, oil and rpm. I understand that I will need NMEA 2000 Sensors installed to deliver this information. Where would I find this sort of harness? Is this an expensive...

egantsea · egantsea

Hi, We have tried to buy one of the Adverc controllers for our 38 hp Beta engine. We have two 100 amp alternators factory installed. We have sent them emails as to where we can purchase the controller but have never heard back. Is there a place in the US where we can purchase one and if not then where and how...

Topic		Started By	Replies	Views	Last Post
	Photos of BV-1505 heat exchanger (Preview) Here are pix of the heat exchanger-high rise exhaust elbow arrangement.MikeB	mikeB	9	2346	Jul 22, 2011 by Williamdement
	Prop spec for bv1505? (Preview) Williamdement wrote 2m, 22s ago:I did my seatrial w/my new bv1505 38 hp and cannot get up past 3000 rpms. I suspect that the prop is limiting. The prop is 18" with pitch of 12. The vessel is a Mariner 36 cutter. I get to hull speed at 2200 to 2500 rpms and after that notice a lot of extraneous water type...	Williamdement	3	606	Jul 19, 2011 by Stanley
	Saving a salt water flooded engine (Preview) I have just helped a friend save his Beta 50 that was flooded with salt water. The initial indication of trouble came, when his fully charged starter battery could not start the engine. On checking the oil, it was found to be a grey colour,(emulsified oil). The first, and most important job, was to fin...	Jenain	0	2773	Jul 14, 2011 by Jenain
	2008 Beta 20 Engine & NMEA 2000 Sensors (Preview) I have a 2008 Beta 20 motor on my sailboat and I was think that I would like to display engine information on my chartplotter such as water temp, oil and rpm. I understand that I will need NMEA 2000 Sensors installed to deliver this information. Where would I find this sort of harness? Is this an expensive...	Jefndeb	1	984	Jul 14, 2011 by Stanley
	Wherer to purchse the Adverc controller? (Preview) Hi, We have tried to buy one of the Adverc controllers for our 38 hp Beta engine. We have two 100 amp alternators factory installed. We have sent them emails as to where we can purchase the controller but have never heard back. Is there a place in the US where we can purchase one and if not then where and how...	egantsea	2	684	Jul 6, 2011 by egantsea
«First < 1 … 99 100 101 102 103 … 146 > Last» \| Page of 146 sorted by