Beta Marine Engines

bdwyer · bdwyer

My tach would work sometimes and now not at all. I checked the connections at the back of the tach and the wiring harness on the engine, but could not find any shorts or bad connections. The other guages work. Any suggestions? Thanks, Barry

chuckm · chuckm

Planning for a Beta marine install. Building a 23 ft wooden double ender, heavy but small. (1) Should you, could you drill shaft bore, at appropriate angle thru floors and sternpost first, then allign engine/tranny to drilled out shaft. Hopefully at a 7 degree angle. (2) What diameter to dril...

chuckm · chuckm

Will this tranny fit to a Kabota 13.5 engine. This transmission came off a universal diesel on a 28 ft sailboat. Its used but a good price on craiglist. Or is it just better to go with a new factory spec tranny that Beta marine sells. Used one is 275$. New one well if its under 800 I would be happy. any thought...

JayBietz · JayBietz

After 10 months the engine Zinc needed replacement and I installed a replacement factory zinc. I also found some threaded zinc rods and they screw in nicely into the brass fitting BUT are about 2X longer then the factory zinc's. Are the longer Zinc's OK to use ie don't block something in the coolen...

MBergmueller · MBergmueller

Hello, I have an Oday 28 that had its OMC saildrive ripped out and replaced by a previous owner. I would like to get rid of the outboard and replace with a Beta. The oday had options for saildrive and shaft drive engines. Mine is a centerboard version with a displacement of 7300lbs. and a beam of 10...

Topic		Started By	Replies	Views	Last Post
	Tach stopped working (Preview) My tach would work sometimes and now not at all. I checked the connections at the back of the tach and the wiring harness on the engine, but could not find any shorts or bad connections. The other guages work. Any suggestions? Thanks, Barry	bdwyer	9	7425	Aug 31, 2010 by Farron Peffer
	Building 23 ft double ender. (Preview) Planning for a Beta marine install. Building a 23 ft wooden double ender, heavy but small. (1) Should you, could you drill shaft bore, at appropriate angle thru floors and sternpost first, then allign engine/tranny to drilled out shaft. Hopefully at a 7 degree angle. (2) What diameter to dril...	chuckm	1	640	Aug 26, 2010 by Farron Peffer
	Hurth HB-50 (Preview) Will this tranny fit to a Kabota 13.5 engine. This transmission came off a universal diesel on a 28 ft sailboat. Its used but a good price on craiglist. Or is it just better to go with a new factory spec tranny that Beta marine sells. Used one is 275$. New one well if its under 800 I would be happy. any thought...	chuckm	2	1042	Aug 25, 2010 by chuckm
	Beta 1505 replacement Zinc Max length? (Preview) After 10 months the engine Zinc needed replacement and I installed a replacement factory zinc. I also found some threaded zinc rods and they screw in nicely into the brass fitting BUT are about 2X longer then the factory zinc's. Are the longer Zinc's OK to use ie don't block something in the coolen...	JayBietz	3	818	Aug 24, 2010 by JayBietz
	Oday 28 sugestions (Preview) Hello, I have an Oday 28 that had its OMC saildrive ripped out and replaced by a previous owner. I would like to get rid of the outboard and replace with a Beta. The oday had options for saildrive and shaft drive engines. Mine is a centerboard version with a displacement of 7300lbs. and a beam of 10...	MBergmueller	6	1964	Aug 18, 2010 by Vic26
«First < 1 … 110 111 112 113 114 … 148 > Last» \| Page of 148 sorted by