Beta Marine Engines

Chris · Chris

Im in the process of installing a new Beta 28 in my 1965 Allied Seabreeze. I'm replacing the existing tank, but plan on keeping the same location which is aft of the engine (secured under the ****pits deck) and above it (top of the tank ~10-12 above engine). Will this present any unique problems sin...

mikeB · mikeB

I have noticed a very small leak around my engine zinc.The only evidence was was a bit of barely noticeable steam while I was running the engine at the dock after a month of remaining idle. I recently replaced the zinc and tightened it as much as I could.Can I use teflon tape around the threads to help seal...

Chris · Chris

Im in the process of installing a new Beta 28 in my 1965 Allied Seabreeze. The engine manual states the raw water intake needs to be 1 dia. Minimum. The boats old Atomic 4 inlet is ~1/2 diameter. I noticed the engines inlet pipe for the raw water pump is ½. My question is since the inlet on the engine is...

JayBietz · JayBietz

Hi: I have about 35 hours on my new Beta 1505 and today when I started the engine to go sailing - I could not control the RPM and it ran very fast until I shut off the fuel supply. I tried to stop the engine with the instrument panel button but that failed also. (Actuating the stop button w/o the engine runn...

mikeB · mikeB

Can I replace the filler cap with any 13pound cap or is there a particular Beta Marine filler cap for my BV-1505? On a routine fluids check I found the coolant level was low. I believe the problem is a leaking coolant filler cap. MikeB

Topic		Started By	Replies	Views	Last Post
	Possible issues of a fuel tank located higher than the engine? (Preview) Im in the process of installing a new Beta 28 in my 1965 Allied Seabreeze. I'm replacing the existing tank, but plan on keeping the same location which is aft of the engine (secured under the ****pits deck) and above it (top of the tank ~10-12 above engine). Will this present any unique problems sin...	Chris	1	960	Dec 7, 2009 by Stanley
	Weeping around zinc. (Preview) I have noticed a very small leak around my engine zinc.The only evidence was was a bit of barely noticeable steam while I was running the engine at the dock after a month of remaining idle. I recently replaced the zinc and tightened it as much as I could.Can I use teflon tape around the threads to help seal...	mikeB	2	776	Nov 23, 2009 by mikeB
	Beta 28hp - Min diameter water inlet (Preview) Im in the process of installing a new Beta 28 in my 1965 Allied Seabreeze. The engine manual states the raw water intake needs to be 1 dia. Minimum. The boats old Atomic 4 inlet is ~1/2 diameter. I noticed the engines inlet pipe for the raw water pump is ½. My question is since the inlet on the engine is...	Chris	2	1163	Nov 18, 2009 by Chris
	BV1505 - Start to max revs' (Preview) Hi: I have about 35 hours on my new Beta 1505 and today when I started the engine to go sailing - I could not control the RPM and it ran very fast until I shut off the fuel supply. I tried to stop the engine with the instrument panel button but that failed also. (Actuating the stop button w/o the engine runn...	JayBietz	15	3669	Nov 9, 2009 by Stanley
	Coolant filler cap (Preview) Can I replace the filler cap with any 13pound cap or is there a particular Beta Marine filler cap for my BV-1505? On a routine fluids check I found the coolant level was low. I believe the problem is a leaking coolant filler cap. MikeB	mikeB	2	970	Nov 2, 2009 by mikeB
«First < 1 … 117 118 119 120 121 … 148 > Last» \| Page of 148 sorted by