Beta Marine Engines

captleasure207 · captleasure207

Hi - I have a Beta 38 and the other day it raced to full RPMs at start up. I was able to get it to shut off with the engine panel stop button. I've removed the throttle cover and saw the rack pin on the injector pin was stuck. I was able to get it unstuck. I also removed the stop solenoid and the T shaped bar inside...

BruceB · BruceB

Is it possible to purchase a Beta43 without panel and senders, and just purchase the components I need for the panel (buzzer, isolating relay for buzzer, and buttons)? If so, what are the thread specs for the temperature and oil senders. I will be purchasing VDO gauges and senders.

BruceB · BruceB

I am going to be creating a custom engine panel for the Beta43 I will be ordering, and need to mockup the panel for the panel manufacturer. There are two reasons I need a custom panel:The C panel won't fit where my panel goes. It's too wide.I want to add a pyrometer, so need to relayout to accommodate the ad...

krivanj · krivanj

I found some 1/4" pencil zincs that seem to be the same as the Camp E-OBC. I screwed both the original brass zinc from the engine and the new ones into a 1/4" female pipe piece I had, and both seemed to screw in without a problem. Anyone see a problem using these in my engine?

dgilliver · dgilliver

I have a oil leak from the bell housing on my Sea Prop 60 saildrive Has anyone else have this problem? I am assuming it is just a bad seal so I will order a new seal before I break the engine and saildrive apart. What else should look for.

Topic		Started By	Replies	Views	Last Post
	Beta 38 racing full RPMs (Preview) Hi - I have a Beta 38 and the other day it raced to full RPMs at start up. I was able to get it to shut off with the engine panel stop button. I've removed the throttle cover and saw the rack pin on the injector pin was stuck. I was able to get it unstuck. I also removed the stop solenoid and the T shaped bar inside...	captleasure207	1	666	Sep 6, 2019 by Stanley
	Customizing engine panel gauges/senders (Preview) Is it possible to purchase a Beta43 without panel and senders, and just purchase the components I need for the panel (buzzer, isolating relay for buzzer, and buttons)? If so, what are the thread specs for the temperature and oil senders. I will be purchasing VDO gauges and senders.	BruceB	6	874	Aug 30, 2019 by BruceB
	Engine Panel hole specs (Preview) I am going to be creating a custom engine panel for the Beta43 I will be ordering, and need to mockup the panel for the panel manufacturer. There are two reasons I need a custom panel:The C panel won't fit where my panel goes. It's too wide.I want to add a pyrometer, so need to relayout to accommodate the ad...	BruceB	4	719	Aug 26, 2019 by BruceB
	BSP vs NPT thread (Preview) I found some 1/4" pencil zincs that seem to be the same as the Camp E-OBC. I screwed both the original brass zinc from the engine and the new ones into a 1/4" female pipe piece I had, and both seemed to screw in without a problem. Anyone see a problem using these in my engine?	krivanj	4	1132	Aug 24, 2019 by BruceB
	Replacing input shaft seal on Sea Prop 60 (Preview) I have a oil leak from the bell housing on my Sea Prop 60 saildrive Has anyone else have this problem? I am assuming it is just a bad seal so I will order a new seal before I break the engine and saildrive apart. What else should look for.	dgilliver	6	842	Aug 19, 2019 by Stanley
«First < 1 … 25 26 27 28 29 … 148 > Last» \| Page of 148 sorted by