Beta Marine Engines

seators · seators

new install of a Beta 16 on my Tartan 30. Feel like i have a pretty good alignment. Have two problems: 1. only getting 3000 rpm in WOT. shaft spins freely by hand. top speed of 5.2 knots. 2. VERY small amount of transmission fluid leaking from behind output flange of transmission. Just enough to w...

Snufle · Snufle

Hi guys, I just thought I'd try asking for help on this forum, as I'm a bit of a novice on engines and have a Beta Marine 14 that won't fire up: The engine died on me on my way into the harbour a couple of weeks back. I noticed the idle was a bit low, and when I tried to increase throttle the rpms didn't increase. I...

Wolf Hound · Wolf Hound

We have a new (to us) boat, re-powered with a Beta 35 engine, which I like very well so far. It's of course a good idea to get better acquainted with the engine, so, when I'm not at the boat (which is about three hours away from our house) I'd like to read through the engine manual. We do have a manual on boa...

Brendan · Brendan

I have overheating problems with my beta 10 . After overheating some gunk appeared in the heat exchanger where you top up the coolant! When idling it will shift 6 litres of seawater/min. but when revved up this does not increase much if at all I have checked the impeller, it's ok I have replaced the therm...

Anomalous · Anomalous

I need to specify the type of cables I need for two Beta enigines with Tecnodrive SD. This is the parameters I have so far to work with and missing information. I checked the operators manual for the engine and the Saildrive. Specifics needed were not listed. The boat is 4hrs away from me so taking a m...

Topic		Started By	Replies	Views	Last Post
	fluid from TMC 40 output flange on Beta 16 installation into Tartan 30 (Preview) new install of a Beta 16 on my Tartan 30. Feel like i have a pretty good alignment. Have two problems: 1. only getting 3000 rpm in WOT. shaft spins freely by hand. top speed of 5.2 knots. 2. VERY small amount of transmission fluid leaking from behind output flange of transmission. Just enough to w...	seators	4	1518	Sep 23, 2012 by seators
	Beta 14 won't start (Preview) Hi guys, I just thought I'd try asking for help on this forum, as I'm a bit of a novice on engines and have a Beta Marine 14 that won't fire up: The engine died on me on my way into the harbour a couple of weeks back. I noticed the idle was a bit low, and when I tried to increase throttle the rpms didn't increase. I...	Snufle	3	2074	Sep 18, 2012 by Stanley
	Beta Manuals Online (Preview) We have a new (to us) boat, re-powered with a Beta 35 engine, which I like very well so far. It's of course a good idea to get better acquainted with the engine, so, when I'm not at the boat (which is about three hours away from our house) I'd like to read through the engine manual. We do have a manual on boa...	Wolf Hound	2	773	Sep 17, 2012 by Wolf Hound
	Overheating (Preview) I have overheating problems with my beta 10 . After overheating some gunk appeared in the heat exchanger where you top up the coolant! When idling it will shift 6 litres of seawater/min. but when revved up this does not increase much if at all I have checked the impeller, it's ok I have replaced the therm...	Brendan	5	2275	Sep 13, 2012 by Brendan
	Throttle and Shift Cable Specifications Needed Throttle Shift Cable (Preview) I need to specify the type of cables I need for two Beta enigines with Tecnodrive SD. This is the parameters I have so far to work with and missing information. I checked the operators manual for the engine and the Saildrive. Specifics needed were not listed. The boat is 4hrs away from me so taking a m...	Anomalous	1	1021	Sep 10, 2012 by Stanley
«First < 1 … 86 87 88 89 90 … 148 > Last» \| Page of 148 sorted by