Beta Marine Engines

bolkowdude · bolkowdude

A few years back, I repowered my little Aquarius Pilot Cutter with a Beta 16 HP BZ602. Great little engine which is now being used by someone else as I sold the boat 3 years ago. Now, I have the most-cool 42' LOD Alden Schooner "Prudence." She is currently powered with a keel-cooled/dry st...

Nemesis · Nemesis

Hello all, I recently completed the replacement of a Yanmar2GM20F with a Beta 20 in my 1993 Tartan 31. Thought I would share some of the experiance with anyone interested. The reason for the replacement was not due to a failure by the Yanmar, it was primarily because I always felt the boat needed a bit m...

marksman · marksman

I was having low water output in my exhaust (BD1005), and found white, chalky deposites encrusting the the raw water portions of the heat exchanger. Mostly on the input/output end and only in the lower half (apperantly the upper half drains into the muffler when engine is shut down). The upper half ha...

MitchWest · MitchWest

I have a Beta 38 with about 1000 hours. When first installed, while running in mid-range speeds (~2500 RPM), the coolant temp never rose above about 165, where the thermostat opens fully. I don't usually run all-out, because I have to pay for the diesel, but when comisioning, I never saw anything o...

Zoe · Zoe

I am installing a Vetus Waterlock exhaust for my Beta 60, my engine injection point of the cooling water is 23cm above the water line. The Vetus manual calls for 15cm Min so all looks well. However looking at my Beta manual it looks like there calling for 30cm Min above the water line, I should mention th...

Topic		Started By	Replies	Views	Last Post
	Repower Time---Again? (Preview) A few years back, I repowered my little Aquarius Pilot Cutter with a Beta 16 HP BZ602. Great little engine which is now being used by someone else as I sold the boat 3 years ago. Now, I have the most-cool 42' LOD Alden Schooner "Prudence." She is currently powered with a keel-cooled/dry st...	bolkowdude	5	1236	Jul 6, 2012 by Stanley
	Engine replacement in a Tartan 31 (Preview) Hello all, I recently completed the replacement of a Yanmar2GM20F with a Beta 20 in my 1993 Tartan 31. Thought I would share some of the experiance with anyone interested. The reason for the replacement was not due to a failure by the Yanmar, it was primarily because I always felt the boat needed a bit m...	Nemesis	0	1350	Jun 6, 2012 by Nemesis
	Heavy white deposites in raw water side of heat exchanger (Preview) I was having low water output in my exhaust (BD1005), and found white, chalky deposites encrusting the the raw water portions of the heat exchanger. Mostly on the input/output end and only in the lower half (apperantly the upper half drains into the muffler when engine is shut down). The upper half ha...	marksman	4	1082	Jun 6, 2012 by marksman
	"Normal" coolant temp? (Preview) I have a Beta 38 with about 1000 hours. When first installed, while running in mid-range speeds (~2500 RPM), the coolant temp never rose above about 165, where the thermostat opens fully. I don't usually run all-out, because I have to pay for the diesel, but when comisioning, I never saw anything o...	MitchWest	2	845	Jun 5, 2012 by MitchWest
	Need for Anti syphon valve? (Preview) I am installing a Vetus Waterlock exhaust for my Beta 60, my engine injection point of the cooling water is 23cm above the water line. The Vetus manual calls for 15cm Min so all looks well. However looking at my Beta manual it looks like there calling for 30cm Min above the water line, I should mention th...	Zoe	3	1740	Jun 5, 2012 by Stanley
«First < 1 … 88 89 90 91 92 … 147 > Last» \| Page of 147 sorted by