Beta Marine Engines

BruceB · BruceB

I am going to be creating a custom engine panel for the Beta43 I will be ordering, and need to mockup the panel for the panel manufacturer. There are two reasons I need a custom panel:The C panel won't fit where my panel goes. It's too wide.I want to add a pyrometer, so need to relayout to accommodate the ad...

krivanj · krivanj

I found some 1/4" pencil zincs that seem to be the same as the Camp E-OBC. I screwed both the original brass zinc from the engine and the new ones into a 1/4" female pipe piece I had, and both seemed to screw in without a problem. Anyone see a problem using these in my engine?

dgilliver · dgilliver

I have a oil leak from the bell housing on my Sea Prop 60 saildrive Has anyone else have this problem? I am assuming it is just a bad seal so I will order a new seal before I break the engine and saildrive apart. What else should look for.

egantsea · egantsea

Hi, We have a Jabsco raw water pump. Jabsco raw water pump 29460-1701 4310 From what I understand they are not made anymore. I saw one on Amazon for $500.00 +. I was told Beta now has a replacement for about $300 USD. We have a dual alternator setup so ours faces back on the right side of the motor....

sbcwylie · sbcwylie

Hello, My Beta 38 has seen only about 135hr of use since installed in the summer of '16. I was about to head out for a couple of weeks and luckily noticed high temp and not enough water coming out of the exhaust before I got too far off the dock. There is corrosion inside the raw water inlet of the heat exch...

Topic		Started By	Replies	Views	Last Post
	Engine Panel hole specs (Preview) I am going to be creating a custom engine panel for the Beta43 I will be ordering, and need to mockup the panel for the panel manufacturer. There are two reasons I need a custom panel:The C panel won't fit where my panel goes. It's too wide.I want to add a pyrometer, so need to relayout to accommodate the ad...	BruceB	4	496	Aug 26, 2019 by BruceB
	BSP vs NPT thread (Preview) I found some 1/4" pencil zincs that seem to be the same as the Camp E-OBC. I screwed both the original brass zinc from the engine and the new ones into a 1/4" female pipe piece I had, and both seemed to screw in without a problem. Anyone see a problem using these in my engine?	krivanj	4	875	Aug 24, 2019 by BruceB
	Replacing input shaft seal on Sea Prop 60 (Preview) I have a oil leak from the bell housing on my Sea Prop 60 saildrive Has anyone else have this problem? I am assuming it is just a bad seal so I will order a new seal before I break the engine and saildrive apart. What else should look for.	dgilliver	6	669	Aug 19, 2019 by Stanley
	Jabsco raw water pump on Beta 38 replacement? raw water pump Jabasco (Preview) Hi, We have a Jabsco raw water pump. Jabsco raw water pump 29460-1701 4310 From what I understand they are not made anymore. I saw one on Amazon for $500.00 +. I was told Beta now has a replacement for about $300 USD. We have a dual alternator setup so ours faces back on the right side of the motor....	egantsea	3	1001	Aug 16, 2019 by Stanley
	Heat exchanger housing corrosion (Preview) Hello, My Beta 38 has seen only about 135hr of use since installed in the summer of '16. I was about to head out for a couple of weeks and luckily noticed high temp and not enough water coming out of the exhaust before I got too far off the dock. There is corrosion inside the raw water inlet of the heat exch...	sbcwylie	20	1065	Aug 9, 2019 by Stanley
«First < 1 … 24 25 26 27 28 … 147 > Last» \| Page of 147 sorted by