Beta Marine Engines

sw61807 · sw61807

I am getting a high oil pressure reading. Starts between 60 and 75. Increases to 100 as I increase the rpms. The only thing I have done recently that would effect the engine is I had my prop repitched. After the repitch I took the boat out and checked how she ran. Was great! I didn't notice the oil pressure...

Chris · Chris

I bought a Beta 28 to replace an aging Atomic 4 on my 1965 35ft Allied Seabreeze. The prop shaft diameter for the Atomic was 7/8, and the Beta 28 specifies a 1 diameter shaft. My initial inspection of the shaft log protruding into the prop cove showed this would not be an issue. Now that Im ready to start...

jaybeegee · jaybeegee

Hello All, I need some spoon feeding to locate the sender unit in my Beta Marine 20 model BD722 as after inserting the ignition key the the three warning lights on the control panel (ie. Battery, Oil Pressure, Temperature) would come on together with the buzzer and once the engine starts they all go of...

egantsea · egantsea

Hi, Remember we just had problems with the heat exchanger stck tube as part of the 250 hr maint. It we got pack on as we posted here. Well we started to remove the impeller cover because we are going to replace the impeller as part of the 250 hour maint schedule. Only it seems antifreeze is coming out of the...

Svboru · Svboru

Hello. Last year, I installed a Beta 16 in my Tartan 30. I've been using the old prop but I can't get up to full RPM so it is time for a propperly sized prop. Because the prop shaft comes out the back of the keel on the Tartan, the prop cannot be larger than 10 inches in diameter. What do you think the right p...

Topic		Started By	Replies	Views	Last Post
	BD1005 oil pressure (Preview) I am getting a high oil pressure reading. Starts between 60 and 75. Increases to 100 as I increase the rpms. The only thing I have done recently that would effect the engine is I had my prop repitched. After the repitch I took the boat out and checked how she ran. Was great! I didn't notice the oil pressure...	sw61807	6	2456	Apr 3, 2013 by Farron
	Shaft Log ID Clearance (Preview) I bought a Beta 28 to replace an aging Atomic 4 on my 1965 35ft Allied Seabreeze. The prop shaft diameter for the Atomic was 7/8, and the Beta 28 specifies a 1 diameter shaft. My initial inspection of the shaft log protruding into the prop cove showed this would not be an issue. Now that Im ready to start...	Chris	1	1231	Mar 18, 2013 by Farron
	newbie asking where is the temperature sender unit?! (Preview) Hello All, I need some spoon feeding to locate the sender unit in my Beta Marine 20 model BD722 as after inserting the ignition key the the three warning lights on the control panel (ie. Battery, Oil Pressure, Temperature) would come on together with the buzzer and once the engine starts they all go of...	jaybeegee	9	2465	Mar 5, 2013 by jaybeegee
	Impeller housing has antifreeze in it? (Preview) Hi, Remember we just had problems with the heat exchanger stck tube as part of the 250 hr maint. It we got pack on as we posted here. Well we started to remove the impeller cover because we are going to replace the impeller as part of the 250 hour maint schedule. Only it seems antifreeze is coming out of the...	egantsea	3	1261	Feb 28, 2013 by Nemesis
	Prop for Tartan 30 (Preview) Hello. Last year, I installed a Beta 16 in my Tartan 30. I've been using the old prop but I can't get up to full RPM so it is time for a propperly sized prop. Because the prop shaft comes out the back of the keel on the Tartan, the prop cannot be larger than 10 inches in diameter. What do you think the right p...	Svboru	1	955	Feb 26, 2013 by Stanley
«First < 1 … 80 81 82 83 84 … 146 > Last» \| Page of 146 sorted by