Beta Marine Engines

alteredcourse30 · alteredcourse30

Jsut wondering the recommended cca for dedicated starting battery - beta20. Also, I ordered the bigger amp... what or can I install /set up ...to monitor (know) teh output of alt and how it is charging the batts... any advice appreciated, thankyou Jamie

JayBietz · JayBietz

Hi: I was doing a spring service on the enging and noticed a lot of black dust on the 100 A alternator. See attached photo. Is this a concern? I assume that I can just vacuum it up. Jay Bietz -- Edited by JayBietz on Sunday 8th of May 2011 08:58:08 PM

egantsea · egantsea

We have had installed a 38hp Beta marine engine with transmission. It replaced a Perkins 4-108 50 hp We have a 36 ft Islander Freeport sail boatOur water heater is higher than the engine. It had a small stainless steel water tank for filling the engine with fluid. Worked good for 32 years with the Perkin...

Zoe · Zoe

On our power boat Beta 60 instalation point X is 8" above the water line is this considerd to close? and the minium should in fact be no less than 12" which is where they show the Anti syphon valve in the manual. Better to be safe than sorry I know. Zoe

alteredcourse30 · alteredcourse30

Hi Stanley..thankyou so much for all your advice last summer....the beta 20 is working great...was inservice around july 2010, oil has been changed once so far....in August (engine and tranny)the engine has about 60hrs on it....For Spring use I was going to change oil and filter, also secondary fu...

Topic		Started By	Replies	Views	Last Post
	engine start batt. (Preview) Jsut wondering the recommended cca for dedicated starting battery - beta20. Also, I ordered the bigger amp... what or can I install /set up ...to monitor (know) teh output of alt and how it is charging the batts... any advice appreciated, thankyou Jamie	alteredcourse30	1	986	May 16, 2011 by Farron
	Beta 1505 - Black dust on alternator (Preview) Hi: I was doing a spring service on the enging and noticed a lot of black dust on the 100 A alternator. See attached photo. Is this a concern? I assume that I can just vacuum it up. Jay Bietz -- Edited by JayBietz on Sunday 8th of May 2011 08:58:08 PM	JayBietz	2	1738	May 9, 2011 by JayBietz
	Water heater higher than motor (Preview) We have had installed a 38hp Beta marine engine with transmission. It replaced a Perkins 4-108 50 hp We have a 36 ft Islander Freeport sail boatOur water heater is higher than the engine. It had a small stainless steel water tank for filling the engine with fluid. Worked good for 32 years with the Perkin...	egantsea	4	1645	May 8, 2011 by Stanley
	Exhaust System Syphoning (Preview) On our power boat Beta 60 instalation point X is 8" above the water line is this considerd to close? and the minium should in fact be no less than 12" which is where they show the Anti syphon valve in the manual. Better to be safe than sorry I know. Zoe	Zoe	1	1634	May 6, 2011 by Stanley
	maintenance - pre-spring checks.... (Preview) Hi Stanley..thankyou so much for all your advice last summer....the beta 20 is working great...was inservice around july 2010, oil has been changed once so far....in August (engine and tranny)the engine has about 60hrs on it....For Spring use I was going to change oil and filter, also secondary fu...	alteredcourse30	7	1307	Apr 29, 2011 by Farron
«First < 1 … 102 103 104 105 106 … 147 > Last» \| Page of 147 sorted by